Sign In | Join Free | My vivirlatino.com
vivirlatino.com
Hebei FUSHENG FRP CO.,LTD
Hebei FUSHENG FRP CO.,LTD
Home > Pultruded Fiberglass Shapes >

Pultruded Fiberglass Shapes

Pultruded Fiberglass Shapes

Contact Now

Cable tray is assembled by pultruded GRP/FRP profiles; suitable for electrical cable, control cables, lightening cable and fittings. There are fiberglass pipe, fiberglass tank, fiberglass tube and vessel.

Advantage:

1.Long service life ( normal design life is 20 years)

2.Convenient installation, and low cost (1/4 SG of carbon steel, no need of fire during construction; length per piece can be 8 m, or more.)

3.Easy to cut, no need of maintenance

Application:

KQJ series cable tray is suitable for voltage below 10 kV electrical cables, control cable, and lightening fitting cables of below 10 kV and the lay out for indoor, outdoor, aerial, channel for cable and tunnel.

Structural features:

KQJ serial cable trays have the features that: widely used, high strength, reasonable structure, low cost, easy for construction, flexible fittings, nice-looking appearance, which make expansion, rebuilding, maintenance much easier.

Installation:

The installation of KQJ series cable tray can be per the local conditions can be laid according to the process requirements, such as plumbing, floor, hoisting under the beam, indoor and outdoor wall, tunnel, cable trench side wall mounted, but also on the open column.

When height of groove of cable tray is 50,100 mm, 6 connection holes for each end; when height of groove of cable tray is 150,200 mm, 12 connection holes for each end.

Support Spacing: it shall be less than or equal load curve, allowable load and support span.

Width: when we are electing the width of cable tray, we should leave enough spare space for new cables in the future.

Separated lying: when there are less power cables and control cables, they can be installed in the same cable tray, but there should be a separation plate between the power cable and control cable.

Fixing of cables: when the cable trays are horizontal laid, the connection point shall be in the position of 1 / 4, horizontal cable shall be fixed every 2 meters, the vertical cable trays shall be fixed every 1.5 meters.

Arrangement of cables in the cable tray

Weak current control cables shall be at the top layer, general control cables and low voltage power cable are downward arrangement. This kind of arrangement is good for shielding; good for cooling and site construction.

Spacing between cable trays

To ensure easy installation, cable tray and the spacing must satisfy the following data:

a ,when we are setting cable trays in the same support beam or in the same horizontal level, the net distance between adjacent cable trays should not be less than 50mm.

b, for two parallel cable tray, its net distance should not be less than 600mm.

When the cable trays are overlapped laid, the vertical distance shall meet the following data:

a, for power cable, it should be 300mm.

b, the control cable, it should be 250mm.

For the convenience of cable tray installation, the distance between cable tray and the top of the ceiling, beams and other obstacles at the bottom should meet the following data:

a, for power cable, it should be not less than 400mm.

b, for control cable, it should be not less than 250mm.

Notes

Vertical cable trays must be protected by cover on the area which is within two meters above the ground.

The position which is liable to mechanical damage must be protected by covers.

When the cable trays are horizontally laid, the selection of stride support shall be per the load curve; when the cable trays are vertically laid, there should be a fixing frame every 1 or 2 meters to make sure the stability of the cable trays.

When the cables in the cable tray are lead from horizontal direction to vertical direction, there must be a guide plate to protect the cable from damage.

When the material of cable tray is steel, there should be a reliable grounding wire; cable trays must be connected with the main grounding wire.


12. SOP Production Line

Our company can produce the whole set of production line of Potassium Sulfate.

This technology is one of most advanced production methods of potassium sulfate. The core is updated new reaction furnace based upon the basis of dry baking method to produce the potassium sulfate. Under the support of the special equipment, it has resolved the abrasion and the corrosion under the condition of high temperature and strong acid and the process problem of continuous output. Comparing with the same equipment from foreign countries, its outstanding characters are little investment, short building duration (four to six months), high atomization reliable quality, high heating efficient, high output, and environment protective.

The design, fabrication, installation, production process, inspection and testing of this whole set of technique and equipment, are completed by our Company singly. We have successfully transferred the whole set of equipment and technique to many firms in Philippines, Indonesia, India, Egypt, etc in recent year, and got good effect.

Welcome clients, friends to our company to visit, consult, and cooperate sincerely.

The technical parameters of the Potassium Sulfate produced by our company are as following:

1. Can reach the following Spec. when Sulfuric acid and potassium chloride are superior quality and have enough time to react:

K2O: 50%min

Moisture content : 0.5%max

Chlorine: 1%max

PH value: 6.5-7

2. Can reach the following Spec. on a large scale in practical industrial production:

K2O: 50%min

Moisture content : 1.5%max

Chlorine : 1.5%max

PH value : 6.5-7


China Customized Inflatable Bumper Ball Game Bubble Adult Grass CE supplier

Pultruded Fiberglass Shapes Images

Inquiry Cart 0
Send your message to this supplier
 
From:
Enter your email please.
To: Hebei FUSHENG FRP CO.,LTD
Subject:
Message:
Characters Remaining: (0/3000)
 
Inquiry Cart 0